Home / Products / Pump Controller / Content

Products

Single Pump Control And Protection Module.

Thank you for choosing our JIT single pump control and protection module. This controller is a module intended to control and protect an individual pump.The user can select a control logic sequence to match their application and enjoy the benefits of superior control and protection for the pumps.

Send Inquiry

Fast Delievery
Quality Assurance
24/7 Customer Service

Product Introduction

There are 3 primary control logic modes:

·'Drainage'where control is concentrated at the source 'Bosting'which references pressure switching on the delivery side for control 'Transfer'which is a mix of source and destination control

The LCD screen displays the pump running state and provides the user a wealth of useful information.

The controller is easy to set up with an initial push button calibration and individual parameters can be fine-tuned.

This controller is particularly useful where there is the need to control and protect pump installations managing the automatic operation through a variety of switching methods without the need to create a bespoke control solution.

Control panel applications:

On the main PCB there is a2 position 'Dip Switch'

To alter the control logic to suit an application,the installer must select the appropriate switch position.

After selecting the desired switch position,cycle the controller power to apply the setting.

	Switch position	Control logic -Applications
1	11	'Pressure Boosting'Mode.Main control via(N/C)pressure switch.Supports run/no run level protection at the source via floats or probes.
2	01	'Drainage'Mode where the control inputs(generally level floats or probes)are located at the source.
3	00	'Transfer'Mode.Main control via control inputs (floats or probes)at destination or by a pressure switch on the delivery line.Supports run/no run level protection at the source.
4	10	Sensorless time control

TECHNICAL SPECIFICATON

Controller Modes	Automatic or Manual operation. Liquid level control via float switch or electrode probes. Pressure control via pressure switch.
Protection functions: Dry run (Underload),Overload,Pump Stalled, Open and reverse phase,Under voltage,Over voltage, Short circuit,Pump Maximum run time
Input Voltage	Single Phase:230V+10%-6% Three Phase: 415V+10%-6%
Rated output power	0.37 to 2.2 kW P2 power (max 15A input) 0.37 to 4 kW P2 power (max 12A input) 2.2 to 7.5 kW P2 power(max 18A input)
Minimum Amperage	1.0 amp to achieve calibration successfully(5 amp for 3-7.5)
Working temp	-25 to+55 deg C 20%to 90%relative humidity,non-condensing
Controller size	200mm wide,275mm tall,125 deep. IP54
Trip response times (set)	Open phase-Less than 2 sec Short circuit-less than 0.1 sec
Trip Voltage (User adjustable)	Over voltage Default =265V Default =460V Under voltage Default =196V Default =340V
Trip response times (User adjustable)	Dry run (Under-load) Under Voltage Over voltage	3 sec Less than 5 sec Less than 5 sec
Recovery times (User adjustable)	Dry run (Under-load) 30 min default Overload 30 min default Under Voltage 5 min default Over voltage 5 min default
Alarms	Audible alarm and flashing screen.Does not support auxiliary alarm

Displaying

This controller display provides a real time indication of the operational mode and the current state of the controller,including real-time voltage/current and any error messages.

Only the icons relevant to the selected operational mode will display.

product-1080-414

Parameter setting

Parameter Item No	Parameter definition	Adjusting range	Default value & remark
001	Dry run protection trip ampere		0.0A
002	Over load protection trip ampere		26.0A(0.75-7.5KW) 52A(11-15KW)
003	Pump stalled protection trip ampere		33.1A(0.75-7.5KW) 66.0A(11-15KW)
004	Under voltage protection trip voltage		175V - Default (Single Phase) 300V - Default (Three Phase)
005	Over voltage protection trip voltage		253V - Default (Single Phase) 439V - Default (Three Phase)
006	Dry run protection trip response time	0-254S	6S - Default Unit is second (S)
007	Dry run protection recovery time	0-254M	5M - Default Unit is minute (M)
008	3 applications if connection with Pure circle timer (Parameter 009-010)	00-01	00 (no) [01 yes]
009	Pure timer control Pump running timer setting	0-254M	5M - Default Unit is minute (M) Pump running timer vaild only the controller is under the application of pure circle timer control.
010	Pure timer control Pump stop timer setting	0-254M	5M - Default Unit is minute (M) Pump stop timer vaild only the controller is under the application of pure circle timer control.
011	Pump stop timer under manual state	0-254M	0M - Default Unit is minute (M) 0M means this stop timer non activated.
012	LCD & button operation lock function	00-01	00 - Default 00= LCD & button operation function non activated 01= LCD & button operation function activated
013	Open phase protection &phase reverse protection enable and disable	00-03	03- Default 00=Open phase protection&phase reverse protection disable 01=Open phase protection disable,phase reverse protection enable 02=Open phase protection enable ,phase reverse protection disable 03=Open phase protection &phase reverse protection enable
*The following* *parameter* *items are* *only* *visible* *when the controller is under the application of temperature control by PT100 temperature sensor and PT100 temperature sensor expansion module equipped.*
014	Pump start temperature	0-100℃	35℃- Default Unit is degree celsius When temperature is below 35℃, pump will start;
015	Pump stop temperature	0-100℃	45℃- Default Unit is degree celsius When temperature is below 45℃, pump will stop;